Publicación: Evolução das tensões residuais no aço inoxidável supermartensítico S13Cr exposto em meios corrosivos
Fecha
2024-10-22
Editor/a
Director/a
Tutor/a
Coordinador/a
Prologuista
Revisor/a
Ilustrador/a
Derechos de acceso
info:eu-repo/semantics/openAccess
Título de la revista
ISSN de la revista
Título del volumen
Editor
Universidad Nacional de Educación a Distancia (España), Universidad de Concepción - Chile. Departamento de Ingeniería Mecánica
Resumen
Estudou-se o comportamento das tensões residuais geradas por retificação, polimento e shot peening em aço inoxidável supermartensítico, submetido a carregamento estático com exposição a dois meios corrosivos. As tensões residuais foram medidas antes dos ensaios de carregamento estático e após cada período de carregamento, utilizando a técnica de difração de raios-X, com o método do sen²ψ. Os resultados mostram que todos os tratamentos (retificação, polimento e shot peening) geraram tensões residuais compressivas, sendo a maior tensão para o shot peening, seguido da retificação e, por fim, do polimento. Com os acabamentos de retificação e polimento, as superfícies das amostras dos corpos de prova retificados e polidos em meios salinos neutros e acidificados em presença de H2S apresentaram uma pequena redução nas tensões residuais, permanecendo ainda em compressão. Embora não tenham sido observadas trincas de corrosão sob tensão, o alívio de tensão foi mais acentuado para a solução ácida do que para a neutra. Isso pode indicar que a presença de tensão compressiva residual pode aumentar a resistência à corrosão deste aço inoxidável.
The behavior of residual stresses generated by grinding, polishing, and shot peening in supermartensitic stainless steel was studied, subjected to static loading with exposure to two corrosive environments. Residual stresses were measured before the static loading tests and after each loading period, using the X-ray diffraction technique with the sin²ψ method. Results show that all treatments (grinding, polishing, and shot peening) generated compressive residual stresses, with the highest stress for shot peening, followed by grinding, and finally polishing. With the grinding and polishing finishes, the surfaces of the samples of ground and polished test specimens in neutral saline and acidified environments with H2S showed a slight reduction in residual stresses, remaining in compression. Although no stress corrosion cracks were observed, the stress relief was more pronounced for the acidic solution than for the neutral one. This may indicate that the presence of compressive residual stress can enhance the corrosion resistance of this stainless steel.
The behavior of residual stresses generated by grinding, polishing, and shot peening in supermartensitic stainless steel was studied, subjected to static loading with exposure to two corrosive environments. Residual stresses were measured before the static loading tests and after each loading period, using the X-ray diffraction technique with the sin²ψ method. Results show that all treatments (grinding, polishing, and shot peening) generated compressive residual stresses, with the highest stress for shot peening, followed by grinding, and finally polishing. With the grinding and polishing finishes, the surfaces of the samples of ground and polished test specimens in neutral saline and acidified environments with H2S showed a slight reduction in residual stresses, remaining in compression. Although no stress corrosion cracks were observed, the stress relief was more pronounced for the acidic solution than for the neutral one. This may indicate that the presence of compressive residual stress can enhance the corrosion resistance of this stainless steel.
Descripción
Organizado y patrocinado por: Federación iberoamericana de Ingeniería Mecánica y Universidad de Concepción - Chile. Departamento de Mecánica, FeIbIm – FeIbEM
Categorías UNESCO
Palabras clave
tensões residuais, usinagem, aço inoxidável supermartensítico, corrosão, residual stresses, machining, supermartensitic stainless steel, corrosion
Citación
-
Centro
E.T.S. de Ingenieros Industriales
Departamento
Mecánica