Persona: Marín Martín, Marta María
Cargando...
Dirección de correo electrónico
ORCID
0000-0003-2686-909X
Fecha de nacimiento
Proyectos de investigación
Unidades organizativas
Puesto de trabajo
Apellidos
Marín Martín
Nombre de pila
Marta María
Nombre
4 resultados
Resultados de la búsqueda
Mostrando 1 - 4 de 4
Publicación Analysis of Force Signals for the Estimation of Surface Roughness during Robot-Assisted Polishing(MDPI, 2018-08-15) Teti, Roberto; Agustina Tejerizo, Beatriz De; Marín Martín, Marta María; Rubio Alvir, Eva MaríaIn this study feature extraction of force signals detected during robot-assisted polishing processes was carried out to estimate the surface roughness during the process. The purpose was to collect significant features from the signal that allow the determination of the end point of the polishing process based on surface roughness. For this objective, dry polishing turning tests were performed on a Robot-Assisted Polishing (RAP) machine (STRECON NanoRAP 200) during three polishing sessions, using the same polishing conditions. Along the tests, force signals were acquired and offline surface roughness measurements were taken at the end of each polishing session. As a main conclusion, it can be affirmed, regarding the force signal, that features extracted from both time and frequency domains are valuable data for the estimation of surface roughness.Publicación Study of Drilling Process by Cooling Compressed Air in Reinforced Polyether-Ether-Ketone(MDPI, 2020-04-22) Domingo Navas, María Rosario; Agustina Tejerizo, Beatriz De; Marín Martín, Marta MaríaThis study is focused on the application of a cooling compressed air system in drilling processes; this environmentally friendly technique allows removing material at very low temperatures, approximately up to −22 °C in the cutting area. The main goals are to find the most improve cutting conditions with less energy consumption, for the drilling of reinforced polyether-ether-ketone with glass fiber at 30% (PEEK-GF30) with cooling compressed air by a Ranque-Hilsch vortex tube, and to find a balance between environmental conditions and adequate process performance. Drilling tests were carried out on plates of PEEK-GF30 to analyze the influence of cutting parameters and environmental temperature (–22, 0 and 22 °C) on variables such as thrust forces, energy and material removed rate by the use of statistical methods; analysis of variance, analysis of means, response surface, and desirability function were employed to identify the optimum region that provides the most improved values of the aforementioned variables. Drill bit diameter was also analyzed to determine the quality of drilled holes. During the drilling processes, force signals were detected by a piezoelectric dynamometer connected to multichannel amplifier and a pyrometer was used to control the temperature. The diameters of the drilled holes were measured by a coordinate measuring machine. Cooling compressed air can be considered an adequate technique to improve the results from an environmental and efficient perspective; in particular, the maximum desirability function was found at a spindle speed of 7000 rpm, a feedrate of 1 mm/rev and a temperature close to −22 °C.Publicación A Multi-Response Optimization of Thrust Forces, Torques, and the Power of Tapping Operations by Cooling Air in Reinforced and Unreinforced Polyamide PA66(MDPI, 2018-03-20) Domingo Navas, María Rosario; Agustina Tejerizo, Beatriz De; Marín Martín, Marta MaríaThe use of cooling air during machining is an environmentally conscious procedure, and its applicability to different processes is a research priority. We studied tapping operations, an important operation in the assembly process, using cooling air with unreinforced polyamide (PA66) and polyamide reinforced with glass fiber (PA66-GF30). These materials are widely used in industry, but their behavior with respect to tapping has not been studied. We analyze the outcomes regarding the thrust force, torque, and power at cutting speeds between 15 and 60 m/min. The experimental tests were executed using cooling air at 22 °C, 2 °C, and −18 °C in dry conditions. The M12 × 1.75 mm taps were high-speed steel, with cobalt as the base material and coatings of TiN and AlCrN. To identify the more influential factors, an analysis of variance was performed, along with multi-response optimization to identify the desirability values. This optimization shows that the optimum for PA66can be found in environments close to 3 °C, while the optimum for PA66-GF30 is found at the minimal temperature studied (−18 °C). Thus, cooling air can be considered an adequate procedure for tapping operations, to increase the sustainability of the manufacturing processes.Publicación Experimental study of magnesium drilling based on the surface quality(Elsevier, 2019) Berzosa Lara, Fernando; Agustina Tejerizo, Beatriz De; Rubio Alvir, Eva María; Marín Martín, Marta MaríaNowadays, the use of magnesium and its alloys for transport applications is based on the combination of high mechanical properties and low density. In general, the machinability of these materials is considered to be good. Nevertheless, it has been reported that the machining of these alloys involves some critical problems regarding their tendency to be flammable at high temperatures and consequently, there is a risk of chip ignition in the working area during the process. This fact is especially critical when the size of chips is reduced. In this study, the influence of cutting conditions on surface roughness, in terms of Ra, obtained by drilling of magnesium alloy (AZ91D-F) was carried out. A factorial design 2 4 was employed for the planning of the drilling tests. The factors considered were the feed rate (0.05 and 0.2 mm/r), cutting speed, 40 and 60 m/min, the type of tool, in particular, the point angle of 118º and 135º, and the cooling system, Dry conditions and MQL (Minimum Quantity Lubrication) system. As main conclusions it can be affirmed that improved surface roughness is obtained with the cutting conditions selected in this study. Furthermore, at 0.05 mm/r and 40 m/min the use of tools with a point angle of 135º provides lower values of Ra than the tool of 118º point angle. Slightly lower values of Ra are obtained with tools of 118º point angle at 0.2 mm/r and 60 m/min.