Persona: Montes Pita, María José
Cargando...
Dirección de correo electrónico
ORCID
0000-0002-2020-8242
Fecha de nacimiento
Proyectos de investigación
Unidades organizativas
Puesto de trabajo
Apellidos
Montes Pita
Nombre de pila
María José
Nombre
13 resultados
Resultados de la búsqueda
Mostrando 1 - 10 de 13
Publicación Proposal of a new design of source heat exchanger for the technical feasibility of solar thermal plants coupled to supercritical power cycles(Elsevier, 2020-10-12) Linares Hurtado, José Ignacio; Montes Pita, María José; Barbero Fresno, Rubén; Rovira de Antonio, Antonio JoséSolar thermal power plants coupled to supercritical CO2 cycles seems to be a way to increase the global solar-to-electric efficiency. For that, the concentrating solar technology that is best integrated is the molten salt central receiver with a thermal energy storage associated. This work is focused on one of the main challenges of this scheme: the source heat exchanger transferring the thermal energy from the molten salt in the solar field to the CO2 in the power cycle. A new design, based on the printed circuit heat exchanger technology is proposed, that withstands the pressure difference and avoids the molten salt plugging when circulating through microchannels. The thermo-mechanic model of this heat exchanger is also calculated. This work also addresses a thermo-economic optimization of the printed circuit heat exchanger proposed. For that, it is considered the global performance of the solar thermal plant for three layouts: recompression, intercooling and partial-cooling cycles. This optimization yields to a great reduction in the investment cost of these source heat exchangers, achieving the lowest cost in the partial-cooling configuration, followed by the intercooling and finally, the recompression. This trend is also observed in the global performance of the solar plant, so the partial-cooling layout is the one with the lowest levelized cost of electricity; this value is similar to that of the intercooling layout, and both are well below from the cost in the recompression layout, which results the most expensive configuration.Publicación Comparison of Different Technologies for Integrated Solar Combined Cycles: Analysis of Concentrating Technology and Solar Integration(MDPI, 2018-04-25) Sánchez, Consuelo; Abbas, Rubén; Muñoz Antón, Javier; Ortega, Guillermo; Rovira de Antonio, Antonio José; Valdés Fernández, Manuel Tomás; Barbero Fresno, Rubén; Montes Pita, María José; Muñoz Domínguez, Marta; Varela Díez, FernandoThis paper compares the annual performance of Integrated Solar Combined Cycles (ISCCs) using different solar concentration technologies: parabolic trough collectors (PTC), linear Fresnel reflectors (LFR) and central tower receiver (CT). Each solar technology (i.e. PTC, LFR and CT) is proposed to integrate solar energy into the combined cycle in two different ways. The first one is based on the use of solar energy to evaporate water of the steam cycle by means of direct steam generation (DSG), increasing the steam production of the high pressure level of the steam generator. The other one is based on the use of solar energy to preheat the pressurized air at the exit of the gas turbine compressor before it is introduced in the combustion chamber, reducing the fuel consumption. Results show that ISCC with DSG increases the yearly production while solar air heating reduces it due to the incremental pressure drop. However, air heating allows significantly higher solar-to-electricity efficiencies and lower heat rates. Regarding the solar technologies, PTC provides the best thermal results.Publicación Analysis and comparison of Integrated Solar Combined Cycles using parabolic troughs and linear Fresnel reflectors as concentrating systems(Elsevier, 2015-11-12) Abbas, Rubén; Rovira de Antonio, Antonio José; Barbero Fresno, Rubén; Montes Pita, María José; Varela Díez, FernandoThis paper compares the annual performance and economic feasibility of Integrated Solar Combined Cycles (ISCC) using two solar concentration technologies: parabolic trough collectors (PTC) and linear Fresnel reflectors (LFR). Integration of solar energy to the steam turbine of a combined cycle gives some advantages: the first one is the fuel saving due to the solar contribution and, additionally, the second one is that this contribution takes place especially in highly insolated periods with high ambient temperatures, when conventional combined cycles decrease their power rate and work with decreased efficiency. Previous works showed the convenience of ISCC using PTC and direct steam generation in locations with severe climatology. Besides, LFR technology is currently considered as a good option for reducing the cost of concentrating solar power. Thus, in the present work both concentrating technologies are studied and compared. Solar contribution is only used for evaporating water, increasing the production of the high pressure level of the steam generator. Two locations, Almeria and Las Vegas, are selected for the annual analyses. Results show that the proposed evaporative configurations increase the annual performance. Also, the thermal contribution is higher with PTC, but LFR may improve the economic feasibility of the plant.Publicación Bibliometric Analysis on Supercritical CO2 Power Cycles for Concentrating Solar Power Applications(MDPI, 2021-09-27) Reyes Belmonte, Miguel Ángel; Guedez Mata, Rafael; Montes Pita, María JoséIn recent years, supercritical CO2 power cycles have received a large amount of interest due to their exceptional theoretical conversion efficiency above 50%, which is leading a revolution in power cycle research. Furthermore; this high efficiency can be achieved at a moderate temperature level; thus suiting concentrating solar power (CSP) applications, which are seen as a core business within supercritical technologies. In this context, numerous studies have been published, creating the need for a thorough analysis to identify research areas of interest and the main researchers in the field. In this work, a bibliometric analysis of supercritical CO2 for CSP applications was undertaken considering all indexed publications within theWeb of Science between 1990 and 2020. The main researchers and areas of interest were identified through network mapping and text mining techniques, thus providing the reader with an unbiased overview of sCO2 research activities. The results of the review were compared with the most recent research projects and programs on sCO2 for CSP applications. It was found that popular research areas in this topic are related to optimization and thermodynamics analysis, which reflects the significance of power cycle configuration and working conditions. Growing interest in medium temperature applications and the design of sCO2 heat exchangers was also identified through density visualization maps and confirmed by a review of research projects.Publicación A novel energy conversion system based on supercritical CO2 recompression Brayton power cycle for power tower concentrating solar plants(Elsevier, 2020-02-09) Linares Hurtado, José Ignacio; Cantizano, Alexis; Sánchez, Consuelo; Montes Pita, María JoséPower tower concentrating solar plants with thermal energy storage will play a key role in the transition to a low carbon scenario, thanks to be a dispatchable renewable energy system. The ternary MgCl2/KCl/NaCl salt appears as one of the most promising due to its lower melting point, higher heat capacity, lower cost and stability up to 800 °C. A cavity-type receiver has been selected because minimizes radiation heat loss at high working temperatures, compared to an external-type receiver, since all commercial selective coatings degrade in air. Supercritical Brayton power cycle is chosen for the power block because it can surpass 50% efficiency, even when working in dry cooling conditions, and printed circuit heat exchangers are usually recommended due to its ability to support the high pressures. However, plugging/clogging issues arise in their small channels when using molten salts. This paper proposes a novel supercritical CO2 Bayton power cycle whose heat power is supplied through the low pressure side (over 85 bar) allowing the use of shell and tube heat exchangers, achieving a higher compactness and a lower investment. Thus, different options based on the recompression layout with intercooling and reheating have been investigated in both dry and wet cooling scenarios. Reheating is recommended for wet cooling, reaching 54.6% efficiency and an investment of 8662 $/kWe; intercooling with reheating is the best option for dry cooling, reaching 52.6% efficiency and an investment of 8742 $/kWe.Publicación Proposal of optimized power cycles for the DEMO power plant (EUROfusion)(Elsevier, 2019-11) Sánchez, Consuelo; Rovira de Antonio, Antonio José; Montes Pita, María José; Muñoz Domínguez, MartaThe objective of this paper is the proposal of two configurations of Rankine cycles different from the standard solution considered for the DEMO 2017 design. The configurations are aimed to maintain as constant as possible the operation at the pulse and dwell modes with minimal fluctuations in the turbine and heat exchangers parameters, in order to maximize the reliability of these components. Each configuration, as well as the reference one, have been simulated both at pulse and dwell operation modes. Compared to the reference design, the proposed configurations are much steadier and mass flow rates in the steam generator and preheaters are constant. In summary, it is possible to ensure a completely steady operation of the whole steam cycle, including all the heat exchangers, without differences between the pulse and dwell modes using two secondary storage tanks additional to the two original molten salt ones.Publicación Optimization of a New Design of Molten Salt-to-CO2 Heat Exchanger using Exergy Destruction Minimization(MDPI, 2020-08-08) Linares Hurtado, José Ignacio; Moratilla, Beatriz Yolanda; Montes Pita, María José; Barbero Fresno, RubénOne of the ways to make cost-competitive electricity, from concentrated solar thermal energy, is increasing the thermoelectric conversion efficiency. To achieve this objective, the most promising scheme is a molten salt central receiver, coupled to a supercritical carbon dioxide cycle. A key element to be developed in this scheme is the molten salt-to-CO2 heat exchanger. This paper presents a heat exchanger design that avoids the molten salt plugging and the mechanical stress due to the high pressure of the CO2, while improving the heat transfer of the supercritical phase, due to its compactness with a high heat transfer area. This design is based on a honeycomb-like configuration, in which a thermal unit consists of a circular channel for the molten salt surrounded by six smaller trapezoidal ducts for the CO2. Further, an optimization based on the exergy destruction minimization has been accomplished, obtained the best working conditions of this heat exchanger: a temperature approach of 50 °C between both streams and a CO2 pressure drop of 2.7 bar.Publicación Thermodynamic Cycles for Solar Thermal Power Plants: A Review(WIREs (Wiley Interdisciplinary Reviews), 2021-10-17) Muñoz Domínguez, Marta; Rovira de Antonio, Antonio José; Montes Pita, María JoséSolar thermal power plants for electricity production include, at least, two main systems: the solar field and the power block. Regarding this last one, the particular thermodynamic cycle layout and the working fluid employed, have a decisive influence in the plant performance. In turn, this selection depends on the solar technology employed. Currently, the steam Rankine cycle is the most widespread and commercially available power block option, usually coupled to a parabolic trough solar field. However, other configurations have been implemented in solar thermal plants worldwide. Most of them are based on other solar technologies coupled to a steam Rankine cycle, although integrated solar Combined cycles have a significant level of implementation. In the first place, power block configurations based on conventional thermodynamic cycles -Rankine, Brayton and combined Brayton-Rankine- are described. The achievements and challenges of each proposal are highlighted, for example, the benefits involved in hybrid solar source/fossil fuel plants. In the second place, proposals of advanced power block configuration are analyzed, standing out: supercritical CO2 Brayton cycles, advanced organic cycles and innovative integrated solar combined cycles. Each of these proposals show some advantages compared to the conventional layouts in certain power or source temperature ranges and hence they could be considered attractive options in the medium term. At last, a brief review of proposals of solar thermal integration with other renewable heat sources is also included.Publicación Maturation of Critical Technologies for the DEMO Balance of Plant Systems(Elsevier, 2022-04-04) Barucca, L.; Hering, B.; Pérez Martin, Sara; Bubelis, E.; Nevo, A. del; Di Prinzio, M.; Caramello, M.; D'Alessandro, A.; Tarallo, A.; Vallone, A.; Moscato, I.; Quartararo, A.; D'amico, S.; Giannetti, F.; Lorusso, P.; Narcisi, V.; Ciurluini, C.; Sánchez, C.; Montes Pita, María JoséThe Pre-Concept Design (PCD) of the Balance of Plant (BoP) systems of the EU-DEMO power plant is described in this paper for both breeding blanket (BB) concepts under assessment, namely the Water Cooled Lithium Lead (WCLL) BB and the Helium Cooled Pebble Bed (HCPB) BB. Moreover, the results of a preliminary evaluation of a number of BoP variants are discussed. This paper outlines the steps of the BoP design development, highlighting the project objectives and the strategy for their achievement under the very challenging requirements which include, among others, the intermittent nature of the DEMO plasma heat source. The main achievements during the PCD Phase will be reported together with the development plan for the Concept Design (CD) Phase to reach a mature (feasible) BoP concept for DEMOPublicación Energy and exergy analysis of microchannel central solar receivers for pressurised fluids(Elsevier, 2023-01-25) Romero, Manuel; González Aguilar, José; Montes Pita, María José; D Souza, David JonathanWithin the new generation of advanced central solar receivers, microchannel pressurised gas receivers are emerging as reliable and efficient alternatives to operate at high temperatures and pressures. This paper presents an optimisation and comparative analysis of different compact plate-fin type structures, constituting the receiver’s absorber panels, classified according to the type of fin arrangement inside: plain rectangular, plain triangular, wavy, offset strip, perforated, and louvred fin. A versatile thermo-fluid receiver model is implemented, allowing simple variation of characteristic geometric parameters of each structure. Exergy efficiency is chosen as the optimisation function, as it considers both heat and pressure losses. The framework of the analysis is set by the receiver’s boundary conditions, operating at the design point conditions of a solar thermal power plant. For each compact structure, the optimal configuration is determined, providing interesting findings that have not been reported in the state-of-the-art to date. Although all geometries show good thermal performance, the perforated and plain rectangular configurations demonstrate the best exergy efficiencies of 59.21% and 58.80%, respectively, favouring taller and narrower channels. This analysis methodology could be seamlessly extrapolated to other gases and working conditions, owing to the thermo-fluid model’s versatility, to reveal the optimal configuration for each case.